The Measurement Tool features 3 Modes.
Standard measurements, Mode 1, are featured in every iGUIDE by default. Advanced Measurements, Modes 2 and 3, are featured as part of every Premium iGUIDE, but can also be added as a paid add-on to Standard iGUIDEs as well.
Read on for instructions on how to use Measurement Modes 1, 2, and 3.
Click here to watch an instructional video about how to use Measurement Modes 1, 2, and 3.
Mode 1 - Measurements on Floor Plan
Measure the horizontal distance between any two points on the floor. This mode is useful for measuring wall to wall distances in irregularly shaped rooms or to see if your furniture will fit.
To use this feature, select Measure Mode 1, then click and drag from one point to another on the floor plan. A red line will connect the start and end points and its length will be reported as shown in Figure 1.
Figure 1. Measuring on a floor plan.
Mode 2 - Measurements on a Vertical Plane
Measure the distance between points located on a vertical plane using a panorama. This mode is useful for measuring features found on walls, such as windows, doors, and ceiling height.
To use this feature, select Measure Mode 2, then click and drag from one point to another on the floor plan to draw a line segment. It will get extended into an infinite line, shown in red, on the floor plan as seen in Figure 2. When projected upwards from the floor, that line will define a vertical plane. All subsequent measurements will be reported as if the points selected in a panorama were located on the plane. Most of the time that plane will be the front surface of a wall visible from the panorama. Click on any two points in the panorama to measure the distance between them. You can zoom into the panorama for more precise positioning.
The two points must be located on the vertical plane you defined, otherwise the reported distance between them will be meaningless.
Figure 2. Measuring in a vertical plane.
Mode 3 - Dual Panorama Triangulation
Measure the distance between any two points in 3D space by using two panoramas. The two points must be clearly visible in both panoramas. This mode is useful for measuring distances that cannot be measured using Mode 1 or Mode 2.
To use this feature, select Measure Mode 3, then select the first panorama that contains the two points of interest and click on those points, remembering the order in which you do that, as shown in Figure 3. You can zoom into the panorama for a more precise positioning. The distance between the two points will initially be shown as “???”. Next, select the second panorama and click the same two points of interest in the same order. You can use zoom again for greater precision. The measurement will appear instead of the three question marks after all four points have been selected, as seen in Figure 4.
It is very important that both panoramas were shot with a camera located on the same horizontal plane (no split-level floors should be used) and using the same tripod height, otherwise the reported distance will be meaningless.
Figure 3. Measuring in 3D space - view from the 1st panorama.
Figure 4. Measuring in 3D space - view from the 2nd panorama.
Multiple Measurements and Undo
You can make multiple measurements in Modes 1, 2, and 3 - just keep selecting new additional points. You can use the Undo button to delete the last point. In Mode 3, Undo will work only until a new pano is selected.
After completing a measurement in Modes 2 and 3 you will receive a message that looks similar to this when a measurement has been taken:
“Estimated measurement uncertainty is 2. Take additional measurements by selecting new start and end points.”
The measurement uncertainty will vary depending on the panoramas selected and the measurement points chosen. Reduce the measurement uncertainty to the lowest possible number by trying the same measurement multiple times, using different panoramas to see what yields the best results.
Figure 5. Keep measurements in the shaded area.
When choosing a panorama in Mode 2 try to use a panorama that is close to features you are trying to measure. This makes selecting the features easier and will reduce measurement uncertainty. This can also be expressed as keeping measurements within a 90° field of view when the panorama’s viewing direction is perpendicular to the vertical plane in which measurements are taken. See the shaded area in Figure 5.
Figure 6. Keep measurements in the shaded area.
When using Mode 3, try to choose panoramas that are close to the features being measured, but that are far enough apart from each other to offer a unique and different perspective. Try to keep measurements out of the periphery of either panorama to reduce measurement uncertainty and aim to keep measurements within the shaded area in Figure 6.
For the iGUIDE Photographer
In order to have optimal panoramas available for measurement you will need to create many panos near objects that could potentially be measured later on. In this way, a little forethought and planning during data capture will lead to more precise measurements by allowing for optimal pano selection later.
To use panos for effective measurement in Mode 3, the iGUIDE IMS-5 camera tripod height must be kept the same while shooting. There is no specific height requirement, but if the camera tripod height is adjusted higher or lower to capture different features, it is recommended that it be returned to its original height to maximize the number of panos that can be used with the Advanced Measurements.
Enabling Advanced Measurements
The Advanced Measurements feature is included with every Premium iGUIDE. However, it can be added to any Standard iGUIDE by checking the box labeled “Advanced Measurements” during creation as seen in Figure 7.
Figure 7. Advanced Measurements on the Create iGUIDE page.
The Advanced Measurements feature can also be purchased at any time after an iGUIDE has been created. You can find out if Advanced Measurements has been activated on your iGUIDE on the Package & Add-ons page as seen in Figure 8.
Figure 8. Advanced Measurements on the Package & Add-ons page.
To toggle Advanced Measurements on or off for any iGUIDE view click the checkbox labeled “Disable Advanced Measurements (if available)” found on the Edit View page.
Figure 9. Advanced Measurements on the Edit View page.
An additional fee will be charged for Advanced Measurements when it is added to a Standard iGUIDE. Click here for pricing information.
Note: Advanced Measurements won’t appear automatically on Premium iGUIDEs created before November 15th, 2019. However, Advanced Measurements can be enabled for any Premium iGUIDE created before this date by finding the property on the iGUIDE Portal and clicking the blue Save button found on the Edit View page. Make sure that the checkbox labeled “Disable Advanced Measurements (if available)” is unchecked.